9702_w24_qp_23
A paper of Physics, 9702
Questions:
7
Year:
2024
Paper:
2
Variant:
3
Login to start this paper & get access to powerful tools
1
Define acceleration. A small aircraft is flying horizontally at a speed of 42 m s–1 at a height of 63 m above horizontal ground, as shown in . 63 m ground speed 42 m s–1 The aircraft drops a small parcel. The parcel is released from the aircraft at the instant shown in . Air resistance is negligible. On , draw a line to show the path of the parcel as it falls from the aircraft to the ground. Calculate the time taken from the instant of release to the instant the parcel reaches the ground. time = s Calculate the vertical component of the velocity of the parcel immediately before it reaches the ground. vertical component of velocity = m s–1 Determine the speed at which the parcel reaches the ground. speed = m s–1
2. Kinematics  →  2.1. Equations of motion
Open
2
State the principle of conservation of momentum. A ball X has mass 240 g and moves in a straight line on a horizontal frictionless surface with an initial speed of 16 m s–1. The ball collides with a stationary ball Y that has mass 480 g. After the collision, ball X is stationary, as shown in . ball X, mass 240 g ball Y, mass 480 g 16 m s–1 BEFORE surface ball X, mass 240 g ball Y, mass 480 g v AFTER surface Show that the speed v of ball Y after the collision is 8.0 m s–1. Calculate the change in the total kinetic energy ∆EK of the balls due to the collision. ∆EK = J The collision in lasts for a time of 2.0 ms. Assume that the contact force between the balls is constant during this time. Determine the magnitude and direction of the force exerted on ball X by ball Y during the collision. magnitude = N direction Compare the magnitude and direction of the force exerted on ball Y by ball X during the collision with the answers in . No further calculations are required.
3. Dynamics  →  3.3. Linear momentum and its conservation
Open
3
State the principle of moments. A rigid uniform beam rests on a pivot at its centre, as shown in . beam pivot x 0.40 m container water h wooden cylinder, weight 4.0 N load, weight 2.6 N (not to scale) A load of weight 2.6 N is suspended from the beam at distance x from the pivot. A wooden cylinder of weight 4.0 N is suspended from the beam at a distance of 0.40 m from the pivot on the opposite side of the pivot to the load. The cylinder rests in a container of water. The lower part of the cylinder is immersed in the water to depth h. Initially, h is equal to 0.10 m and x is equal to 0.40 m. The system is in equilibrium. Use the principle of moments to show that the upthrust U exerted by the water on the cylinder is 1.4 N. The density of the water is 1.0 × 103 kg m–3. Calculate the area A of the circular cross-section of the cylinder. A = m2 More water is gradually added to the container in , so that depth h in gradually increases. The length x is continuously adjusted so that the system remains in equilibrium. On , sketch the variation of x with h. Use the space below for any working. 0.10 0.2 0.4 0.6 0.8 0.15 0.20 0.25 0.30 h / m x / m 0.35 0.40
4. Forces, density and pressure  →  4.2. Equilibrium of forces
4. Forces, density and pressure  →  4.1. Turning effects of forces
6. Deformation of solids  →  6.1. Stress and strain
Open
4
Define: stress strain. Two wires X and Y, with equal unstretched lengths of 0.84 m, are suspended from fixed points that are at the same horizontal level. The lower ends of the wires are attached to a beam of negligible mass. The beam is horizontal and in equilibrium, as shown in . beam wire Y wire X load, 18 N Wire X is made from a metal that has a Young modulus of 1.9 × 109 Pa. Wire Y is made from a different metal. A load of weight 18 N is suspended from the beam at a point that is equidistant from the two wires. This load causes both wires to extend by 0.47 mm. Determine the cross-sectional area of wire X. cross-sectional area = m2 Wire Y has a greater diameter than wire X. Explain, without calculation, whether the Young modulus of the metal from which wire Y is made is less than, the same as or greater than 1.9 × 109 Pa.
6. Deformation of solids  →  6.1. Stress and strain
Open
5
A stationary wave is formed on a string XY that has a length of 0.48 m. shows the string at one instant in time. 0.48 m X Y The speed of the wave on the string is 1400 m s–1. On , draw a cross (×) at one position that is a node and another cross at one position that is an antinode. Label the node N and the antinode A. Show that the wavelength of the wave produced is 0.32 m. Explain your reasoning. Calculate the frequency of the wave. frequency = Hz A source of sound waves of frequency 780 Hz is on a rotating platform. The speed of the source is 39 m s–1. The sound is detected by an observer that is a large distance from the rotating platform, as shown in . platform observer source of sound, speed 39 m s–1 (not to scale) The speed of sound in air is 320 m s–1. Calculate the maximum frequency of the sound detected by the observer. maximum frequency = Hz At time t = 0, the observer detects the sound emitted by the source when it was in the position shown in . On , sketch the variation with t of the frequency f of the sound detected by the observer for one complete rotation of the platform. Calculations are not required. t f
7. Waves  →  7.3. Doppler effect for sound waves
8. Superposition  →  8.1. Stationary waves
Open
6
Define resistance. A cylindrical metal wire of length 2.4 m and cross-sectional area 8.0 × 10–6 m2 has a resistance of 0.33 Ω. There is a current in the wire of 4.7 A. Determine the resistivity of the metal from which the wire is made. resistivity = Ω m Calculate the charge that passes through the wire in a time of 5.0 minutes. charge = C The free electrons (charge carriers) in the wire have an average drift speed of 0.16 mm s–1. Determine the number density of charge carriers in the metal. number density = m–3 The wire in may be considered to be a fixed resistor. It is connected in series with a thermistor to a battery that has negligible internal resistance. Use circuit symbols to complete to show the circuit diagram of this arrangement. Explain, without calculation, how the power dissipated in the wire changes as the temperature of the thermistor is increased.
9. Electricity  →  9.3. Resistance and resistivity
9. Electricity  →  9.1. Electric current
Open