9702_w18_qp_42
A paper of Physics, 9702
Questions:
12
Year:
2018
Paper:
4
Variant:
2
Login to start this paper & get access to powerful tools
1
State what is meant by gravitational field strength. Explain why, at the surface of a planet, gravitational field strength is numerically equal to the acceleration of free fall. An isolated uniform spherical planet has radius R. The acceleration of free fall at the surface of the planet is g. On , sketch a graph to show the variation of the acceleration of free fall with distance x from the centre of the planet for values of x in the range x = R to x = 4R. 0.25 g 0.50 g 0.75 g 1.00 g acceleration of free fall R 2R 3R 4R x The planet in has radius R equal to 3.4 × 103 km and mean density 4.0 × 103 kg m–3. Calculate the acceleration of free fall at a height R above its surface. acceleration of free fall = m s–2
13. Gravitational fields  →  13.3. Gravitational field of a point mass
13. Gravitational fields  →  13.4. Gravitational potential
Open
2
State what is meant by an ideal gas. An ideal gas comprised of single atoms is contained in a cylinder and has a volume of 1.84 × 10–2 m3 at a pressure of 2.12 × 107 Pa. The mass of gas in the cylinder is 3.20 kg. Determine, to three significant figures, the root-mean-square (r.m.s.) speed of the atoms of the gas. r.m.s. speed = m s–1 The temperature of the gas in the cylinder is 22 °C. Determine, to three significant figures, 1. the amount, in mol, of the gas, amount = mol 2. the mass of one atom of the gas. mass = kg Use your answer in part 2 to determine the nucleon number A of an atom of the gas. A =
15. Ideal gases  →  15.2. Equation of state
15. Ideal gases  →  15.3. Kinetic theory of gases
Open
3
Define specific latent heat of fusion. A student sets up the apparatus shown in in order to investigate the melting of ice. A V + – heater pure melting ice beaker water The heater is switched on. When the pure ice is melting at a constant rate, the data shown in are collected. voltmeter reading / V ammeter reading / A initial mass of beaker plus water / g final mass of beaker plus water / g time of collection / minutes 12.8 4.60 121.5 185.0 5.00 The specific latent heat of fusion of ice is 332 J g–1. State what is observed by the student that shows that the ice is melting at a constant rate. Use the data in to determine the rate at which 1. thermal energy is transferred to the melting ice, rate = W 2. thermal energy is gained from the surroundings. rate = W
14. Temperature  →  14.3. Specific heat capacity and specific latent heat
16. Thermodynamics  →  16.2. The first law of thermodynamics
Open
4
A U-tube contains liquid, as shown in . liquid L x x The total length of the liquid column is L. The column of liquid is displaced so that the change in height of the liquid level from the equilibrium position in each arm of the U-tube is x, as shown in . The liquid in the U-tube then oscillates such that its acceleration a is given by the expression a L g x =-d n where g is the acceleration of free fall. Show that the liquid column undergoes simple harmonic motion. The variation with time t of the displacement x is shown in . –2.0 –1.0 +1.0 +2.0 x / cm 0.25 0.50 0.75 1.00 1.25 1.50 t / s Use data from to determine the length L of the liquid column. L = m The oscillations shown in are damped. Suggest one cause of this damping. Calculate the ratio total energy of oscillations after 1.5 complete oscillations total initial energy of oscillations ratio =
17. Oscillations  →  17.1. Simple harmonic oscillations
Open
5
In radio communication, the radio wave is usually modulated. State what is meant by amplitude modulation (AM ). A sinusoidal radio carrier wave has a frequency of 900 kHz and an unmodulated amplitude measured to be 4.0 V. The carrier wave is amplitude modulated by a signal of frequency 5.0 kHz. For the amplitude modulated wave, determine the wavelength, wavelength = m describe the amplitude variation, state the bandwidth. bandwidth = Hz Communication is sometimes made using satellites in geostationary orbits that have a period of rotation about the Earth of 24 hours. State two other features, apart from the period, of a geostationary orbit. 1. 2. Suggest why 1. frequencies of the order of gigahertz are used for satellite communication, 2. the uplink frequency to the satellite is different from the downlink frequency.
7. Waves  →  7.1. Progressive waves
17. Oscillations  →  17.1. Simple harmonic oscillations
Open
6
State what is meant by the electric potential at a point, the relationship between electric potential at a point and electric field strength at the point. Two similar solid metal spheres A and B, each of radius R, are situated in a vacuum such that the separation of their centres is D, as shown in . R R sphere A charge +Q D P x sphere B charge +q The charge +Q on sphere A is larger than the charge +q on sphere B. A movable point P is located on the line joining the centres of the two spheres. The point P is a distance x from the centre of sphere A.
18. Electric fields  →  18.5. Electric potential
18. Electric fields  →  18.3. Electric force between point charges
Open
7
A circuit incorporating an ideal operational amplifier (op-amp) is shown in . – + VOUT –5.0 V 2.4 kΩ 1.8 kΩ +5.0 V +5.0 V RT R The variation with temperature θ of the resistance RT of the thermistor is shown in . 3.0 3.1 3.2 3.3 3.4 RT / k Ω / °C θ The output potential VOUT of the op-amp circuit changes sign when the temperature of the thermistor is 4.0 °C. Calculate the resistance R. R = kΩ State and explain whether the output potential VOUT is +5.0 V or −5.0 V for a thermistor temperature of 2.5 °C. The output of the op-amp is to be displayed using two light-emitting diodes (LEDs) labelled G and B. When the temperature of the thermistor is below 4.0 °C, only the LED labelled G emits light. The LED labelled B emits light only when the temperature of the thermistor is above 4.0 °C. On , draw and label the symbols for the two LEDs.
9. Electricity  →  9.3. Resistance and resistivity
10. D.C. circuits  →  10.3. Potential dividers
10. D.C. circuits  →  10.1. Practical circuits
Open
8
Define magnetic flux density. A stiff copper wire is balanced horizontally on a pivot, as shown in . 7.5 cm pivot stiff wire P Q S R Sections PQ, QR and RS of the wire are situated in a uniform magnetic field of flux density B produced between the poles of a permanent magnet. The perpendicular distance of PQRS from the pivot is 7.5 cm. When a current of 2.7 A is passed through the wire, a small mass of 45 mg is placed a distance 8.8 cm from the pivot in order to restore the balance of the wire, as shown in . 7.5 cm 8.8 cm 2.7 A 2.7 A pivot stiff wire P Q S R pole pieces of magnet small mass Explain why, when the current is switched on, the current in the sections PQ and RS of the wire does not affect the balance of the wire. The length of section QR of the wire is 1.2 cm. Calculate the magnetic flux density B. B = T
20. Magnetic fields  →  20.2. Force on a current-carrying conductor
20. Magnetic fields  →  20.5. Electromagnetic induction
20. Magnetic fields  →  20.4. Magnetic fields due to currents
Open
9
A Hall probe is placed near one end of a solenoid that has been wound on a soft-iron core, as shown in . V + – solenoid soft-iron core Hall probe The current in the solenoid is switched on. The Hall probe is rotated until the reading VH on the voltmeter is maximum. The current in the solenoid is then varied, causing the magnetic flux density to change. The variation with time t of the magnetic flux density B at the Hall probe is shown in . –2 –1 B / mT t1 t2 t3 t4 t At time t = 0, the Hall voltage is V0. On , draw a line to show the variation with time t of the Hall voltage VH for time t = 0 to time t = t4. V H V 0 t1 t2 t3 t4 t The Hall probe in is now replaced by a small coil of wire connected to a sensitive voltmeter, as shown in . V solenoid soft-iron core small coil of wire + – The magnetic flux density, normal to the plane of the small coil, is again varied as shown in . On , draw a line to show the variation with time t of the e.m.f. E induced in the small coil for time t = 0 to time t = t4. E t1 t2 t3 t4 t
20. Magnetic fields  →  20.3. Force on a moving charge
20. Magnetic fields  →  20.5. Electromagnetic induction
20. Magnetic fields  →  20.4. Magnetic fields due to currents
Open
10
The root-mean-square (r.m.s.) value of the voltage of a sinusoidal alternating supply is 9.9 V. The frequency of the supply is 50 Hz. Derive an expression for the variation with time t (in second) of the potential difference V (in volt) of the supply. V = Explain the function of the non-uniform magnetic field superposed on the large constant magnetic field in diagnosis using magnetic resonance imaging (NMR. A parallel beam of X-rays of intensity I0 is incident normally on some soft tissue and bone, as illustrated in . incident intensity I0 transmitted intensity I 0.40 cm soft tissue bone 1.8 cm The bone is 0.40 cm thick and the total thickness of the bone and the soft tissue is 1.8 cm. The intensity of the transmitted beam is I. Data for the linear attenuation coefficient μ of bone and of soft tissue are given in . μ / cm–1 bone soft tissue 2.9 0.92 Calculate, in dB, the ratio transmitted intensity I incident intensity I0 . ratio = dB
24. Medical physics  →  24.1. Production and use of ultrasound
24. Medical physics  →  24.2. Production and use of X-rays
Open
11
State what is meant by a photon. Describe the appearance of a visible line emission spectrum, as seen using a diffraction grating. The lowest electron energy levels in an isolated hydrogen atom are shown in . – 0.54 –1.50 –13.6 energy / eV – 0.38 – 3.40 – 0.85 (not to scale) An electron is initially at the energy level –0.85 eV. State the total number of different wavelengths that may be emitted as the electron de-excites (loses energy). number = Photons resulting from electron de-excitation from the –0.85 eV energy level are incident on the surface of a sample of platinum. Platinum has a work function energy of 5.6 eV. Determine 1. the maximum kinetic energy, in eV, of a photoelectron emitted from the surface of the platinum, maximum energy = eV 2. the wavelength of the photon producing the photoelectron in part 1. wavelength = m
22. Quantum physics  →  22.2. Photoelectric effect
22. Quantum physics  →  22.1. Energy and momentum of a photon
24. Medical physics  →  24.3. PET scanning
Open
12
State what is meant by nuclear fusion and nuclear fission. nuclear fusion: nuclear fission: A nuclear reaction which may, in the future, be used for the generation of electrical energy is H H + He x + . Name the particle x. Data for the binding energy per nucleon EB of some nuclei are given in . binding energy per nucleon EB / 10–13 J deuterium H tritium H helium He 1.7813 4.5285 11.3290 1. State the binding energy per nucleon of x. binding energy per nucleon = J 2. Calculate the energy change that takes place in this reaction. energy change = J Use your answer in part 2 to determine the energy release when 2.0 g of deuterium ( H 2 ) reacts with 3.0 g of tritium ( H 3 ). energy = J To avoid the issue of disclosure of answer-related information to candidates, all copyright acknowledgements are reproduced online in the Cambridge International Examinations Copyright Acknowledgements Booklet. This is produced for each series of examinations and is freely available to download at www.cie.org.uk after the live examination series.
23. Nuclear physics  →  23.1. Mass defect and nuclear binding energy
Open