0625_w20_qp_42
A paper of Physics, 0625
Questions:
11
Year:
2020
Paper:
4
Variant:
2
Login to start this paper & get access to powerful tools
1
A sky-diver jumps out of a hot-air balloon, which is 4000 m above the ground. At time = 30 s, she opens her parachute. is the speed-time graph of her fall. speed m / s time / s 4.0 Label with the letter X the point on the graph where the sky-diver opens her parachute. Label with the letters Y and Z the two parts of the graph where the sky-diver falls at terminal velocity. Describe, in terms of the forces acting on the sky-diver, her motion between leaving the balloon and opening her parachute. Calculate the average speed of the sky-diver in the first 4.0 s of her fall. average speed =
1. Motion, forces and energy  →  1.2. Motion
Open
2
Define the moment of a force about a point. shows a uniform rod of wood suspended from a pivot. 0.75 m 0.25 m 34° centre of mass pivot rod of wood F W (not to scale) The rod is held stationary by a horizontal force F acting as shown. The mass of the rod is 0.080 kg. Calculate: the weight W of the rod weight = the moment of W about the pivot moment = the moment of F about the pivot moment = the force F. force = The angle between the rod and the vertical is increased. State whether the force F needed to hold the rod stationary must be increased, decreased or stay the same. Explain your answer.
1. Motion, forces and energy  →  1.5.2. Turning effect of forces
Open
4
shows a thermometer. ice cubes wire of material A wire of material A wire of material B water at 0 °C water at 100 °C V The voltmeter reading is 5.4 mV. State the name of this type of thermometer. shows the same thermometer used to measure the temperature of liquid X. water at 20 °C liquid X V With the setup in , the voltmeter reading is 1.7 mV. Calculate the temperature of liquid X measured by the thermometer. temperature = Suggest an application for which this type of thermometer is more suitable than a liquid-in- glass thermometer.
2. Thermal physics  →  2.2.2. Specific heat capacity
2. Thermal physics  →  2.2.3. Melting, boiling and evaporation
Open
5
Define specific latent heat. Explain the melting of a solid in terms of molecules and energy. An electrical heater is used to heat a liquid to its boiling point. shows the apparatus. balance heater element liquid container 3800 g connecting wires When the liquid is boiling, the heater supplies 1.26 MJ of thermal energy. The mass reading shown on the balance decreases from 3800 g to 2300 g. Calculate the specific latent heat of vaporisation of the liquid. specific latent heat = State and explain a precaution to improve the accuracy of the value of specific latent heat calculated in .
2. Thermal physics  →  2.2.2. Specific heat capacity
2. Thermal physics  →  2.2.3. Melting, boiling and evaporation
Open
6
shows a transverse wave produced in a string. string (full size) On : draw labelled lines to show 1. the amplitude of the wave 2. the wavelength of the wave label a trough with the letter T. A person vibrates one end of the string vertically to produce the wave. He makes 15 complete oscillations in 60 s. Show that the speed of the wave is 2.0 cm / s. State the difference between transverse waves and longitudinal waves. Use your ideas about the direction of oscillations. transverse waves longitudinal waves
3. Waves  →  3.1. General properties of waves
3. Waves  →  3.4. Sound
Open
7
shows a ray of light passing through an optical fibre. Q P i The optical fibre is made of glass that has a refractive index of 1.4. No light refracts from the fibre at points P and Q. State the name of the process that occurs at P and Q. Calculate the minimum value of angle i for there to be no refraction at point P. angle = State and explain the use of optical fibres in medicine. The ray of light shown in is monochromatic light from a laser. State what is meant by monochromatic light. Use one of the following quantities in your answer. amplitude brightness frequency refractive index speed
3. Waves  →  3.2.2. Refraction of light
Open
9
shows a bar magnet and four plotting compasses A, B, C and D. D B bar magnet A C On : draw an arrow on each of the three plotting compasses B, C and D to show the direction of the magnetic field label the magnetic poles of the bar magnet N and S. Describe one method for demagnetising a bar magnet. represents a current in a wire. The current is into the plane of the paper. Draw the pattern of the magnetic field produced around the wire. Show clearly the direction of the magnetic field. The direction of the current in the wire is reversed. The magnitude of the current is unchanged. State the effect that reversing the current has on the magnetic field produced.
4. Electricity and magnetism  →  4.1. Simple phenomena of magnetism
4. Electricity and magnetism  →  4.5.3. Magnetic effect of a current
Open
10
shows an incomplete electrical circuit. 2.0 Ω 6.0 Ω 4.0 Ω E C F D A B A student completes the circuit and measures the current in the 6.0 Ω resistor. On , draw an ammeter symbol in one gap and straight lines to indicate wires in the other gaps to show how the student should do this. A voltmeter is connected to measure the potential difference (p.d.) across the 4.0 Ω resistor. On , draw a voltmeter symbol connected in the correct position. With the circuit completed, the current in the 2.0 Ω resistor is 2.5 A. Calculate the current in the 6.0 Ω resistor. current = shows the same electrical circuit with an alternating current (a.c.) power supply and a wire in the gap AB. 2.0 Ω 6.0 Ω 4.0 Ω E C F D A B On , draw a diode symbol in one gap and a straight line to indicate a wire in the other gap so that there is a current from right to left in the 4.0 Ω resistor and an alternating current in the 2.0 Ω resistor.
4. Electricity and magnetism  →  4.2.4. Resistance
4. Electricity and magnetism  →  4.3.3. Action and use of circuit components
Open
11
State two differences between nuclear fission and nuclear fusion. Radioactive tracers emitting γ-rays can be used in medicine. The half-life of the source of these γ-rays is 6 hours. Explain why a source of γ-rays used in this way should not have a half-life shorter or longer than about 6 hours. Technetium-99 is a source of γ-rays often used as a radioactive tracer. It is produced from molybdenum-99 which emits β-particles. The symbol for technetium is Tc and the symbol for molybdenum is Mo. Complete the nuclide equation for this decay. 42 Mo Tc + β Technetium-99 is a radioactive nuclide. State another use of radioactive nuclides in medicine.
5. Nuclear physics  →  5.2.4. Half-life
5. Nuclear physics  →  5.2.3. Radioactive decay
Open